Share This Article
Not everyone wants to “add” parts to their new dirt bikes, which is fine, but for those that must tinker, we put together a “Top 5” must haves that we would recommend. We will be doing these “Top 5” articles with all of the new 450F/250F machines and will be splitting the information up between pulpmx.com and keeferinctesting.com. These mods are recommended, by us, through countless hours of testing. If you don’t find a specific aftermarket company that you prefer in this article, don’t fret, email me at kris@keeferinctesting.com and we can talk it out like adults should. Again, we will not push something on you unless we know it works. These mods that are in this article will work for the 2018.5/2019/2019.5 Husqvarna FC450 and Rockstar Edition models.
1. ECU Re-Map: The 2019.5 Husqvarna FC450 Rockstar Edition still feels a little rich on bottom end and lean on top end. The 2019.5 ECU settings are slightly better than my 2018.5 that I purchased, but it’s still not close to where it needs to be. Getting a simple re-flash of your ECU from Jamie at Twisted Development will help the sluggish feel off the bottom and get you more bottom-mid range RPM response. It will make the “light on paper” FC450/Rockstar Edition actually feel light on the track. If you can’t splurge for the Vortex ignition then go with a re-flash of your stock ECU. This is my first “MUST HAVE” on this machine. It will change the character of the Husqvarna for the better.
2. Black Throttle Cam: A close second to getting this sucker better through corners is installing the black throttle cam so there isn’t a huge lag in response mid-corner. With the standard throttle cam the bike comes on soft and then has a big hit that can upset your rolling corner speed. THIS DRIVES ME NUTS! Installing the black cam will help the transition at 0-15% throttle opening through corners. Some dealers will install this cam before purchase, but it’s good for you to check by simply unbolting your throttle housing and checking your throttle tube for the black throttle cam.
3. 14/52 Gearing: Want to make your shock feel better and help your third gear pulling power? Try going to a 14/52 gearing and you’ll notice a slightly better third gear pull as it could possibly make leaving your RE in third gear through corners much easier. Going up to a 14/52 gearing ratio also helps relax the shock under load, which makes connectivity to the rear wheel more positive. I have tried 13/49 gearing and although it has better recovery than the stock 13/48 and 14/52 gearing, the 13/49 set up didn’t add to the shock’s/rear end comfort like the 14/52 ratio did. Try it!
4. Handlebars/Bar Bend: I have tinkered way too much with this over the past couple years, but I feel like I have finally honed in on a good handlebar bend. I have stuck with Pro Taper’s SX Race bend for my style of riding and my height. The SX Race bend is slightly taller than the stock Husqvarna bend (+7mm), but is not so tall where it affects my corners. The SX Race bend also comes standard with a length of 800mm, which is the exactly the right amount of length most of us are looking for. The stock Husqvarna bend is long (811mm) and gives me a hard to lean feel through corners. I also went with a Fuzion (crossbar style) bar, but that is simply just preference as I could easily go back to a Pro Taper EVO style as well.
5. Airbox Mod: You want a little more excitement out of your Husqvarna’s low end? Drill some 1/2 inch holes in the left side airbox cover (as shown) and you’ll get some increased throttle response throughout the RPM range. Rumor has it that all FC Husqvarna’s will be coming with pre-drilled air vents come 2020. The Husqvarna airbox is smaller than the KTM so there his more benefit on the track doing this to the Husqvarna versus the KTM.
Extras: Kris what about suspension? The AER fork is decent and I can ride with it, but yes of course I would recommend a set of WP Cone Valve forks if you want maximum comfort and front end traction. Do you need a Trax shock? The answer is, “no”. The stock shock is quite good and has tons of comfort. Yes, you can run CV forks with a stock shock. I’ve done it and it works just fine. The AER fork performance is good, but still will change on you throughout a long day of riding.
Keep an eye on motor mounts, spokes, and sprocket bolts as they come loose because of the Husqvarna’s vibration. Yes, the steel frame bikes vibrate a little more than the aluminum frame bikes, so that means you need to check bolts more often.
