Share This Article
I am just the average nine to fiver and weekend warrior. I get up at 4AM, go to work, and think about dirt bikes (probably like most other riders out there). I walk through the race pits, drool over the factory machines, and wish I could just have one piece of eye candy that graces the factory riders machines. This is where Ride Engineering decided to give their CRF450R clamp that factory Honda like touch. They took their CRF450R clamp, moved the logos, and anodized them cherry red just like Ken Roczen’s factory machine. The Ride Engineering factory 450RWE triple clamp retains the stock 22mm offset that comes on 17-19 CRF450’s and can be used in conjunction with the stock bar mounts or Ride Engineering’s one piece bar mount.
Ride Engineering worked to try and make this Honda triple clamp retain the stock clamp characteristics (flex/rigidity balance). They also used 2024 aluminum, which is the same alloy aluminum that a lot of the factory teams use for their clamps. Just to add to the factory flare we put the new clamp on the scale and it weighed in at 7.9oz. lighter than the OEM clamp! The 450WE clamp fits both the previous 48mm and the new 49mm Showa forks. It also fits 2013-2019 Honda CRF450R, 2017-2019 CRF450RX, 2014-2019 CRF250R and let’s not forget the 2019 CRF450RWE. This is not Ride Engineering’s first rodeo as they have been building triple clamps with different offsets to help change the character of motocross machines for years.
Installation was a breeze as any novice mechanic can handle this job with a little time in the garage. I would suggest using the owner’s manual as torque specs are always crucial when it comes to suspension components. The torque spec on Keefer’s 2019 CRF450R test bike is: (upper pinch bolt 16 lb-ft, lower pinch bolts 15 lb-ft, and steering stem nut 80 lb-ft). As I hit Sunrise MX on my usual Saturday track day, I was not only excited to ride after a long work week, but I was hoping one of my favorite aspects of the new Honda (front end feel) was not gone. To my delight it was really hard to pick apart any huge differences between the two clamps on the track. As I put down my 30+2 lap moto (Thank you Kris Keefer! Yes, that is sarcasm) the Honda retained that front end feel that I loved with the stock clamp, but I did notice two small differences after I put more time on them. The Ride Engineering clamp does make the front end “turn in” slightly easier and also gives me a little firmer front end feel on hard pack square edge. This wasn’t a drastic difference, but it is something I noticed after a few hours on the clamps. I am a heavier guy at over 200 pounds so a little firmer feel wasn’t a deal breaker for me. I am the type of rider that is very sensitive to vibration or any unwanted feed back through the bars so I was pleased that I didn’t get any increased vibration. Ride-Engineering utilizes the stock rubber’s for their bar mounts and this helps retain that OEM comfort while adding cushion over some other solid mounted bar mounts I tried last time. If you’re a vet rider and are looking for more comfort, make sure your bar mounts are rubber mounted! The Honda’s cornering manners were kept in tact, but with just a little more positive lean in, I did notice that the bar position was slightly more comfortable which I discovered most on deeply tilled up tracks/soil. The Ride Engineering clamp only has one location to mount the bars, but I did notice that the bar position was slightly more comfortable. The mounting position on the Ride Engineering clamps locates the bars three millimeters forward over the OEM mounting location. If you don’t like this bar location you can always turn around the stock bar mounts to pull the bars back.
As you can tell the Ride Engineering CRF450RWE triple clamp is more of a factory look than a clamp that gives more performance. Having said that Ride Engineering does offer different offset triple clamps for the Honda CRF450R that come in 20mm, 21mm, and stock 22mm offsets. They also come in a black or red colorway. These other offset sizes are not the “450RWE” clamps and will have a Ride Engineering logo on the side. On a side note; try to keep the Ride Engineering colored triple clamps covered up from the bright sun. Too much sun (like sitting in the pits for an extended period of time) will fade the color a little. I simply put a towel over my bars to help shade the triple clamps as much as I can. The CRF450RWE clamp includes the top clamp, bottom clamp, pressed in stem, and lower bearing and it retails for $549.90. You can check out all of Ride’s accessories over at Ride-Engineering.com and take a look at what they have to offer for your trusty steed.
Matthew Sirevaag 205lb Novice
Full Time Electrician/Husband/Father/Dirt Bike Fanatic